Grage Aeromodelling

Tinggal tunggu Nongolnya kapan yach.....

Turnigy 9XR Prototype


mungkin msh prototype om...

ni om ada info dari http://txrxnews.blogspot.com

New Turnigy 9xR confirmed !
Hobbyking have posted a few tweets this week confirming the new 9xR is in the works. There is very little info available, but I can quote the following from twitter:

" module based with inbuilt 2.4 antenna plus options for FASST, DSMX & long range 433mhz plus it looks & feels much nicer."

" 9X will be replaced by 9XR later this year (worth the wait, trust me)"

" its been 18 months in the making. I should have more information soon. - Anthony"

Photos should be released in a few months. That's all we know for now but I'll update when any info is forthcoming and buy one for review as soon as they are released.

Update on the Turnigy 9XR
From HK:


- The 9XR has a pin-out in the battery compartment for easier custom firmware flashing without needing to open the case.
- It will use the atmega chip and can be flashed with your existing customised software. In fact, it comes standard with a similar rom to ER9x.
- Backlit screen
- Has inbuilt and module based antenna system
- Spare parts available
- Improved switch and pot quality
- The 9XR will be $50.00
- We're working with Frsky on a module for the 9XR

mudah mudahan kualitasnya sama or lebih baek dr pendahulu nya

rivan000 wrote:ni om ada info dari http://txrxnews.blogspot.com

New Turnigy 9xR confirmed !
Hobbyking have posted a few tweets this week confirming the new 9xR is in the works. There is very little info available, but I can quote the following from twitter:

" module based with inbuilt 2.4 antenna plus options for FASST, DSMX & long range 433mhz plus it looks & feels much nicer."

" 9X will be replaced by 9XR later this year (worth the wait, trust me)"

" its been 18 months in the making. I should have more information soon. - Anthony"

Photos should be released in a few months. That's all we know for now but I'll update when any info is forthcoming and buy one for review as soon as they are released.

Update on the Turnigy 9XR
From HK:


- The 9XR has a pin-out in the battery compartment for easier custom firmware flashing without needing to open the case.
- It will use the atmega chip and can be flashed with your existing customised software. In fact, it comes standard with a similar rom to ER9x.
- Backlit screen
- Has inbuilt and module based antenna system
- Spare parts available
- Improved switch and pot quality
- The 9XR will be $50.00
- We're working with Frsky on a module for the 9XR

wih..cuma $50.00

@Zaki, mandiridjaya, nomind: Iyah.. Hehe..tentengannya sesuatu banget
Tapi mudah2an firmware-nya okeh.. Sy dah pake yg Turnigy9X tp dgn modul
Frsky DJT, so far oke. Tapi ada tapinya, stick aileron itu kalo digerakkan ke kiri-kanan di channel Throttle kena pengaruh(dilihat dimenu display). Sama stick di throttle itu kalo dr 0 digerakkan sampe ke 100, belum sampe 100 petunjuk dimenu display sdh menunjukan full

Nice.... Mudah2an cepet rilis, dengan harga yg terjangkau pastinya....

wijayanto wrote:Nice.... Mudah2an cepet rilis, dengan harga yg terjangkau pastinya....

eh,ada om vijay nih..

endycute wrote:eh,ada om vijay nih..

hai oom endy ... ketemu disini

Kalau bener akan direlease , 9XR akan sangat mantep baik dari segi hardware maupun software ..

Here is a Feature List:
input voltage 6.5 - 16 volts (7.2V ideal)
Atmel SAM3S ARM Cortex M3 Microprocessor
256K of Eprom , 48K Ram
4mb EEprom - For Model /sound storage
Support for Optrex display F-55472GNFJ-SLW-AAN
Built-in external USB socket for Programming / interface.
2 external RS232 Serial Ports.
PWM control of LED backlight . (dimmable)
1/2 Watt Mono Audio Amp , with digital volume control
8 ohm speaker output with auto switch over headphone jack output.
Micro SD card socket with 4 bit high speed connection to ARM
Support for RN-42 Bluetooth Module (spot for external TTL serial connection)
Haptic output connector , with PWM drive.
ATTiny167 AVR micro for RTC and 12 external switch inputs/encoders or up to 10 A/D inputs , can be battery backuped
External I/O connector with 4 lines one with DAC output
I2C output connector + spare port pin.
5V output.
On board current sensor , to measure power usage on battery
Second PPM OUTPUT
Software control of Power - off