Moderator: widodo
budi.santoso wrote:Kalo sy baru pake tx Turnigy9X dgn modul frsky dan rx seri V8.
Menurut specifikasinya sih ditulis bisa setting failsafe.
Apakah sudah ada yg nyoba atau mungkin memang bisa disetting failsafenya(kebetulan sy belum nyoba)?
Salam,
... mohon infonya !!!
Wind Raider wrote:Oh ya , saya barusan baca di forum HK ; ternyata TGY 9x ini bisa dikalibrasi sticknyaInstructions for calibration as below:
1. Push the right lower trim tab to the left and the left side trim tab up, and while holding them, turn the Tx on. You will get a screen that shows the version number of the firmware, with four zeroes (0000) at the top of the screen.
2. Center both sticks in their range in all axis, and press the menu button until it beeps and release. The screen number will change to 0001.
3. Move the right stick to the upper right corner, and press menu, and you should get a beep, and the number on the screen will change to 0002.
4. Put the right stick in the lower left corner, and press menu, and get a beep, and the number will change to 0003.
5. Release the right stick, and put the left stick in the upper right corner, and press menu, get the beep, and the number will change to 0004.
6. Put the left stick in the lower left corner, and press menu again, get the beep and the number will change to 0005.
7. Center both sticks, and press menu, get the beep. You are done calibrating the sticks.
While at the same screen, press the + key, the screen will change, and you will get the position of the controls in hex code. You can see the numbers change as you move the sticks or knobs. Press - to go back to the firmware version screen. Exit the firmware screen, and go to the Display menu item. As long as you haven't turned the TX off, you will see the hex codes for stick positions for the 4 primary controls. Once you turn the tx off and back on, and go back to the Display menu item, the numbers will disappear.
link : http://hobbyking.com/hobbyking/forum/fo ... ?TID=16099
Ini sekalian ada link cara utk membersihkan potensio :
http://www.rcgroups.com/forums/showpost ... count=3401
nah suhu apakah ada ya beli potensionya kalo mau ganti dikhawatirkan nanti sewaktu waktu aus lagi 
anakpahuluan wrote:budi.santoso wrote:Kalo sy baru pake tx Turnigy9X dgn modul frsky dan rx seri V8.
Menurut specifikasinya sih ditulis bisa setting failsafe.
Apakah sudah ada yg nyoba atau mungkin memang bisa disetting failsafenya(kebetulan sy belum nyoba)?
Salam,
Nanya om.....!!!!
Kalo TX turnigy pake modul Frsky ..... tipe yang mana V8FT atau V8JT
omi wrote:mau ikut nanya, soalnya punya turnigy error :
masalahnya saat di switch di -On kan, bisa muncul menu tapi di enter menu dll, cuma bunyi tit tapi ga bisa masuk ke menu lainnya... seperti hang gitu
kira2 perlu diapakan ya? apa perlu di flash/upgrade firmware.. tapi ga tau caranya?
atau di lem biru saja ya
mohon bantuaannya
novianwf wrote:omi wrote:mau ikut nanya, soalnya punya turnigy error :
masalahnya saat di switch di -On kan, bisa muncul menu tapi di enter menu dll, cuma bunyi tit tapi ga bisa masuk ke menu lainnya... seperti hang gitu
kira2 perlu diapakan ya? apa perlu di flash/upgrade firmware.. tapi ga tau caranya?
atau di lem biru saja ya
mohon bantuaannya
coba lebih lama om nekan menunya
Dedy1186 wrote:mohon bantuan suhu smua...RX yg ber FAILSAFE merk / jenis apa ya yg cocok dengan turnigy x9 ? trimakasih
klo mo ganti sama modul tx nya baru ada merk corona ato frysky ato assan 
galih sundayana wrote:unding wrote:Maksud dari suhu WR yg ini
terima kasih banyak tambahan nya,,,betul2 memperjelas...
