[TGY 9X ] Maen simulator tanpa cabut modul

[Abdinik]

OK suhu...saya akan coba pasang resistornya, sambil belajar nyolder.
Alhamdulillah nyolder sudah mulai mulus n rapi.
tapi cara tersebut bisa di Aplikasikan ke tx Flysky 9Ch kan suhu???
kalo tidak salah Flysky 9Ch n turnigy 9Ch n Imax 9Ch cuma beda merk saja y suhu tapi isinya sama??
terima kasihsuhu

[rasyidrisyad]

Maaf agak telat membalasnya .
Pemasangan resistor spt itu tidak mempengaruhi range karena hanya merupakan semacam switch logika .

... memang harus 1K ya suhu? mohon pencerahannya ...

[Wind Raider]

Tidak harus 1 K sih .
Latar belakang kenapa demikian bisa dibaca di : http://er9x.googlecode.com/svn/trunk/doc/PPMinFix.pdf

Ini kutipannya :
The ppm signal is from a pin of a micro-controller, which can provide about 20 mA current.
If you put a resistor in the path where you want the switch or relay to be, this will solve
the problem. A 1 kohm resistor will work fine, as explained below:

1. It will provide the required voltage level to the trainer even if the ppm signal is shortcircuited
by the RM module. The pin which produce the ppm signal usually has a output
resistance about 200 ohm. When the ppm signal is shorted to ground, the level of the
ppm signal sent to the trainer is still very high, 1000 / (1000 + 200) percent by using
voltage divider, which is good enough for the trainer.

2. It will provide the required voltage level to the RF module if the RM module is on. The
reason is that when the RF module is powered, the input resistance of the ppm input pin
will be very high, and 1 kohm resistance will not have noticeable effect.

You may ask if I have tried the easy method already. The answer is yes. I just did both of
my two radios, and they are all working fine with whatever RF module.
A picture can be posted at a later time if it is needed.

Cheers,
JH

[rasyidrisyad]

Tidak harus 1 K sih .
Latar belakang kenapa demikian bisa dibaca di : http://er9x.googlecode.com/svn/trunk/doc/PPMinFix.pdf

Ini kutipannya :
The ppm signal is from a pin of a micro-controller, which can provide about 20 mA current.
If you put a resistor in the path where you want the switch or relay to be, this will solve
the problem. A 1 kohm resistor will work fine, as explained below:

1. It will provide the required voltage level to the trainer even if the ppm signal is shortcircuited
by the RM module. The pin which produce the ppm signal usually has a output
resistance about 200 ohm. When the ppm signal is shorted to ground, the level of the
ppm signal sent to the trainer is still very high, 1000 / (1000 + 200) percent by using
voltage divider, which is good enough for the trainer.

2. It will provide the required voltage level to the RF module if the RM module is on. The
reason is that when the RF module is powered, the input resistance of the ppm input pin
will be very high, and 1 kohm resistance will not have noticeable effect.

You may ask if I have tried the easy method already. The answer is yes. I just did both of
my two radios, and they are all working fine with whatever RF module.
A picture can be posted at a later time if it is needed.

Cheers,
JH

... makasih suhu ilmunya...
oh iya, mau tanya nih suhu, seting tuk turunin warning tegangan rendah dimana nya?
Baterai di 9.0 V beep nya nyala trus, jadi keganggu.... dan mau nyobain pake baterai 2S kalo bisa.
Thx sebelumnya...

[Wind Raider]

Buka Menu SETUP
Kemudian cari Sub Menu BAT WARNING
Setel batas tegangan disitu .

[ekop123]

Buka Menu SETUP
Kemudian cari Sub Menu BAT WARNING
Setel batas tegangan disitu .

Pagi Pak,

Mohon info mengenai manual book Turnigy 2,4GHZ 9x ada tidak ya Pak....? kebetulan 2 hari yang lalu saya dikasih hadiah oleh Suhu Iwan, atas ultah saya yang ke 17 Mohon Pencerahannya Pak, terima kasih

[yoyonh]

Buka Menu SETUP
Kemudian cari Sub Menu BAT WARNING
Setel batas tegangan disitu .

Pagi Pak,

Mohon info mengenai manual book Turnigy 2,4GHZ 9x ada tidak ya Pak....? kebetulan 2 hari yang lalu saya dikasih hadiah oleh Suhu Iwan, atas ultah saya yang ke 17 Mohon Pencerahannya Pak, terima kasih

Saya punya pak Eko, merk IMAX9X tapi sama saja, cuma beda nama. pdf 25MB.
gak bisa di email, kegedean.
Cuman saya siang inii mau ke Cirebon, mudah mudahan besok malam bisa sampai lagi Bekasi jadi Minggu bisa saya bawain di USB.

[rasyidrisyad]

Buka Menu SETUP
Kemudian cari Sub Menu BAT WARNING
Setel batas tegangan disitu .

... makasih suhu wind atas ilmunya,
di TGY 9X saya cuma ada menu System Seting dan menu Funct Seting, jadi gak nemu Menu SETUP, mohon pencerahannya lagi suhu, lalu batas tegangan terendah tuk TX ini berapa suhu?
supaya gak sampai ngedrop atau ngeganggu daya pancar nya?
ma'af suhu ngerepotin dan gak bosen jawab ....

[ekop123]

Buka Menu SETUP
Kemudian cari Sub Menu BAT WARNING
Setel batas tegangan disitu .

Pagi Pak,

Mohon info mengenai manual book Turnigy 2,4GHZ 9x ada tidak ya Pak....? kebetulan 2 hari yang lalu saya dikasih hadiah oleh Suhu Iwan, atas ultah saya yang ke 17 Mohon Pencerahannya Pak, terima kasih

Saya punya pak Eko, merk IMAX9X tapi sama saja, cuma beda nama. pdf 25MB.
gak bisa di email, kegedean.
Cuman saya siang inii mau ke Cirebon, mudah mudahan besok malam bisa sampai lagi Bekasi jadi Minggu bisa saya bawain di USB.

Mercy Pak Haji..............

[Wind Raider]

di TGY 9X saya cuma ada menu System Seting dan menu Funct Seting, jadi gak nemu Menu SETUP, mohon pencerahannya lagi suhu, lalu batas tegangan terendah tuk TX ini berapa suhu?
supaya gak sampai ngedrop atau ngeganggu daya pancar nya?
ma'af suhu ngerepotin dan gak bosen jawab ....

ohhhh firmwarenya masih yg original ya ?
kalau gitu mesti ngoprek dikit pak .. mainkan di pembagi tegangan pada sensor tegangan .
langkah2nya ada di :
http://www.rcmodelreviews.com/tendollarbattery.shtml
( 4 halaman hehehe )